TR & TRCC- 3Φ
What Are You Looking For?
Explore Our Products
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/100mA |
| Make | Autodata |
| Type | TR-95/100 |
| Power | 10.35 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 14 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 100 mA |
| Output Power | 9.5 kW |
| Efficiency | 89% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 440litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 500 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 400 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 300 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator and breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 9.5 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 100 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/100 |
| Rated voltage output | 415 V |
| Rated Current output | 14 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 150 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 55A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | Default RS485 Modbus communication |
| Open communication is optional | |
| HMI | 4.3" Snowy IV Touch screen display unit for single field |
| 7" Hadock Touch screen display unit for Multiple field | |
| Built in Rapper provision | Provided (Optional) |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/150mA |
| Make | Autodata |
| Type | TR-95/150 |
| Power | 15.25 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 21 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 150 mA |
| Output Power | 14.25 kW |
| Efficiency | 90% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 440litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 500 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 700 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 400 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator and breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 14.25 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 150 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/150 |
| Rated voltage output | 415 V |
| Rated Current output | 21 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 200 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 55A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/150mA |
| Make | Autodata |
| Type | TR-95/150 |
| Power | 15.25 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 21 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 150 mA |
| Output Power | 14.25 kW |
| Efficiency | 90% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 440litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 500 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 700 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 400 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator and breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 14.25 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 150 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/150 |
| Rated voltage output | 415 V |
| Rated Current output | 21 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 200 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 55A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/200mA |
| Make | Autodata |
| Type | TR-95/200 |
| Power | 20.7 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 29 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 200 mA |
| Output Power | 19 kW |
| Efficiency | 91% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 440litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 500 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 800 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 450 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator and breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 19 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 200 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/200 |
| Rated voltage output | 415 V |
| Rated Current output | 29 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 200 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 55A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/250mA |
| Make | Autodata |
| Type | TR-95/250 |
| Power | 25.6 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 36 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 250 mA |
| Output Power | 23.75 kW |
| Efficiency | 90% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 440litres |
| Dielectric strength of oil (with 2.5mm) | >60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 500 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 1300 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 700 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 23.75 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 250 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/250 |
| Rated voltage output | 415 V |
| Rated Current output | 36 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 250 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 90A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/300mA |
| Make | Autodata |
| Type | TR-95/300 |
| Power | 30.5 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 42 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 300 mA |
| Output Power | 28.5 kW |
| Efficiency | 92% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 440litres |
| Dielectric strength of oil (with 2.5mm) | >60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 500 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 1100 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 600 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 28.5 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 300 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/300 |
| Rated voltage output | 415 V |
| Rated Current output | 42 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 250 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 90A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/400mA |
| Make | Autodata |
| Type | TR-95/400 |
| Power | 41.4 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 58 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 400 mA |
| Output Power | 38 kW |
| Efficiency | 92% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 480litres |
| Dielectric strength of oil (with 2.5mm) | >60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 600 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 1500 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 750 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 38 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 400 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/400 |
| Rated voltage output | 415 V |
| Rated Current output | 58 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 350 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 110A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/600mA |
| Make | Autodata |
| Type | TR-95/600 |
| Power | 62 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 86 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 600 mA |
| Output Power | 57 kW |
| Efficiency | 93% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 580litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 700 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 2400 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 900 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator and breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 57 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 600 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/600 |
| Rated voltage output | 415 V |
| Rated Current output | 86 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 550 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 160A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/700mA |
| Make | Autodata |
| Type | TR-95/700 |
| Power | 73 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 102 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 700 mA |
| Output Power | 66.5 kW |
| Efficiency | 93% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 600litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 800 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 2800 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 1000 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator and breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 66.5 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 700 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/700 |
| Rated voltage output | 415 V |
| Rated Current output | 102 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 600 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 250A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/800mA |
| Make | Autodata |
| Type | TR-95/800 |
| Power | 82 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 114 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 800 mA |
| Output Power | 76 kW |
| Efficiency | 93% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 640 litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 900 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 3300 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 1400 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt Manual |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 76 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 800 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/800 |
| Rated voltage output | 415 V |
| Rated Current output | 114 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 700 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 250A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/900mA |
| Make | Autodata |
| Type | TR-95/900 |
| Power | 92.6 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 129 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 900 mA |
| Output Power | 85.5 kW |
| Efficiency | 93% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 680 litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 1000 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 3500 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 1500 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | Inbuilt Manual |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 85.5 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 900 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/900 |
| Rated voltage output | 415 V |
| Rated Current output | 129 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 750 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 250A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/1000mA |
| Make | Autodata |
| Type | TR-95/1000 |
| Power | 103 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 143 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 1000 mA |
| Output Power | 95 kW |
| Efficiency | 93% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 700litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 1100 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 3800 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 1600 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | External Manual |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 95 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 1000 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/1000 |
| Rated voltage output | 415 V |
| Rated Current output | 143 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 800 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 250A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/1200mA |
| Make | Autodata |
| Type | TR-95/1200 |
| Power | 123.4 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 172 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 1200 mA |
| Output Power | 114 kW |
| Efficiency | 93% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 720litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 1200 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 4600 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 1800 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | External Manual |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 114 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 1200 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/1200 |
| Rated voltage output | 415 V |
| Rated Current output | 172 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 850 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 250A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |
Rapper control system is designed specifically for ESP application. This rapper control system is designed to be used with electrical solenoid type impact rappers. These rappers are also called as magnetic impulse gravity impact (MIGI) rappers. Field installed RDB panel has provided with special type of diode.
- PLC based rapper systems
- 7″ Touchscreen HMI for operation.
- Matrix type & Non matrix type configuration
- Open communication protocol interface with plant DCS systems.
- Easy maintenance
- Suitable for ESP application in industries like Sugar plant, Cement plant, steel plant, Power plant, etc.
| RECTIFIER/ TR SET | 95KVP/1500mA |
| Make | Autodata |
| Type | TR-95/1500 |
| Power | 154.3 kVA |
| Rated Primary Voltage | 415 V |
| Suitable for Voltage variation | ±10% |
| Rated primary Current | 215 Amps |
| Rated Frequency | 50 Hz |
| Suitable for Frequency variation | ± 5% |
| No of phases primary | 3-ph |
| Output Voltage | 95 kVP DC at no load |
| Output Current | 1500 mA |
| Output Power | 142.5 kW |
| Efficiency | 93% |
| No. of Primary taps supplied | Nil |
| Tap Voltage | Not applicable |
| 1 minute power frequency withstand voltage | 3 kV |
| Impulse withstand voltage | 170 kVP (Only for transformer) |
| % of impedance system | 33 % ±10% |
| Enclosure protection | IP 55 |
| Transformation Ratio | 97.8 |
| Form factor | Voltage – 0.74,Current – 0.82 |
| Type of Cooling | ONAN |
| Type of Oil | Mineral Oil as per IS:335 |
| Total oil requirement (approx.) | 770litres |
| Dielectric strength of oil (with 2.5mm) | 60 kV |
| Flash Point of oil | >140°C |
| Type of oil level gauge | Sight Glass |
| No Load losses at expected operating voltage | 1500 W (Subject to IS tolerance) |
| Load losses (Short Circuit) | 5500 W (Subject to IS tolerance) |
| Miscellaneous losses if any | 2200 W |
| Class of Insulation | Class A |
| TR Unit construction | Hermetically sealed without conservator without breather |
| HT Bushing orientation | Horizontal |
| Earthing Switch | External Manual |
| Class of insulating winding | |
| (I) L.V. | Class A |
| (II) H.V. | Class B |
| Range of Oil Temperature Indicator | 0° C – 120° C |
| Class of L.V. bushing | 1.1 kV Class |
| Class of H.V bushing | Suitable for 95 kVP DC |
| Creepage distance of HV Bushing | Min. 750 mm |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | > 60 microns |
| List of TR set Protection | Pressure Release Valve |
| Oil Temp. Indicator – I – Alarm | |
| Oil Temp. Indicator – II – Trip | |
| Pressure High – Trip | |
| Low Oil Level – Trip | |
| TR set Grounded – Trip | |
| RECTIFIER | |
| Type | Full Wave Bridge |
| Make | Autodata |
| Diode type | Avalanche Diode |
| Rating | 142.5 kW |
| Half wave/full wave rectification | Full wave rectification |
| Rated current output of each rectifier set | 1500 mA |
| Rated voltage output of each rectifier set | 95kV Peak at no load |
| Peak inverse voltage of diode bridge | 226 kV |
| No of Earthing terminal | 2 |
| Voltage feedback | 10VDC at rated kV peak |
| Current feedback | 5V DC at rated average current |
| TR Control Panel | |
| Make | Autodata |
| Type | TRCC 95/1500 |
| Rated voltage output | 415 V |
| Rated Current output | 215 Amps |
| Rated frequency | 50 Hz |
| Heat dissipation of panel | 1000 W |
| Panel enclosure protection | IP 42 |
| Suitable for Voltage variation | ±10% |
| Suitable for Frequency variation | ±5% |
| Thyristor rating | Min. 330A |
| Type of over voltage protector | G. D. Tube |
| No. Of Earthing terminal | 2 |
| Paint Shade | RAL 7032, Siemens Grey |
| Painting thickness in microns | >50 microns |
| Controller | Calculus |
| Communication | |
| HMI | |
| Built in Rapper provision |